Dayton Audio ND25FW-4
Dayton Audio ND25FW-4 1” Soft Dome Neodynium Tweeter with Waveguide 4 Ohm Dayton Audio has added a waveguide faceplate to the popular ND25 soft dome to create the ND25FW-4 tweeter. The waveguide faceplate controls dispersion to minimize ceiling and wall reflections, which in turn leads to an increase in efficiency across most of the passband. Key Features Waveguide loaded 1" treated silk dome Waveguide provides controlled directivity and higher efficiency Low Fs of 1,350 Hz can accommodate crossovers as low as 2,500 Hz Includes foam gasket to ensure a good seal to your enclosure High-strength neodymium motor with heatsink and ferrofluid cooling Standard 104 mm diameter faceplate for easy integration into many existing systems Dayton Audio ND25FW-4 1" Soft Dome Neodymium Tweeter with Waveguide 4 Ohm The Dayton Audio ND25FW-4 tweeter features a unique integrated round waveguide faceplate that provides a controlled directivity transition at high frequencies, reducing the effect of room reflections on the speaker's tonal balance. Unlike conventional flat-faceplate dome tweeters whose directivity does not match the midwoofer driver near the crossover frequency, the ND25FW-4's waveguide is curved to maintain consistent directivity at the transition. The waveguide also acts as a low-compression horn, lowering distortion. Waveguide-loaded dome tweeters are embraced within the industry for providing directivity control and mild horn loading without the negative effects of compression loading such as impulse smear and throat distortion where high levels are not needed. The waveguide profile used in the ND25FW-4 provides a minimum dispersion angle of about 90 degrees, and maintains directivity control to about 2,000 Hz, but the round waveguide will install easily into the same 104 mm standard tweeter cutout used commonly by dome tweeters with larger ferrite motors. Specifications: • Power handling: 20 watts RMS/40 watts max • VCdia: 1" • Le: 0.04 mH • Impedance: 4 ohms • Re: 3.2 ohms • Frequency response: 2,500-20,000 Hz • Fs: 1350 Hz • SPL: 91 dB 1W/1m • Dimensions: Overall diameter: 4.09", Cutout diameter: 2.875", Depth: 1.57".
Dayton Audio ND25FA-4
Dayton Audio ND25FA-4 1” Soft Dome Neodynium Tweeter Dayton Audio's compact, ultra-smooth ND25FA-4 soft dome tweeter features excellent detail and high power handling. The small faceplate and neodymium motor make it easy to keep center-to-center distance to a minimum for improved off-axis response, and the exceptionally flat response above 3 kHz. Key Features Exceptionally flat treble response with low distortion Compact round faceplate design is simple to install High-strength neodymium motor with heatsink and ferrofluid cooling Perfect for placement in car A-pillars 1" diameter voice coil for good off-axis dispersion and excellent power handling Clean, modern styling and appearance Dayton Audio ND25FA-4 1" Soft Dome Neodymium Tweeter This tweeter is smooth! The Dayton Audio ND25FA-4 1" soft-dome tweeter combines an exceptionally flat response above 3 kHz with a compact round faceplate for a clean, modern appearance that integrates easily into any design. The tiny yet powerful neodymium motor structure features an aluminum heatsink and ferrofluid cooling for low power compression and improved long-term power handling. A copper pole cap within the motor further reduces distortion and inductance effects. Choose the ND25FA-4 when you need detail that won't become fatiguing or shrill at high volumes, for a highly refined presentation. The compact faceplate allows close center-to-center spacing of drivers, making these tweeters perfect for line array use or D'Appolito (MTM) configurations with wide dispersion.
Dayton Audio AMTHR-4
Dayton Audio AMTHR-4The Dayton Audio AMTHR-4 Air Motion Transformer is a 4-ohm tweeter designed for high-resolution audiodeveloped and can reach frequencies from 2kHz to 40kHz with a power handling of 25 wattskann.This wide frequency range goes beyond the range of human hearing and captures everyNuance of your favorite music. This leads to a more intense listening experience, where every sound detailremain.
GRS PT2522-4
With a low mass diaphragm and powerful motor, the GRS PT2522-4 planar back tweeter delivers high efficiency output with excellent transient response. The open back construction produces true dipole radiation which is ideal for use in open baffle designs. Smooth frequency response and low distortion gives the PT2522-4 an incredibly natural but dynamic sound. Key Features Extremely low mass diaphragm provides excellent transient response and accuracy Large diaphragm produces high efficiency and wide bandwidth Remarkably flat response even at 30 degrees off axis Open back delivers true dipole radiation for use in open baffle designs Linear impedance simplifies crossover design Shallow mounting depth for use in low profile designs The GRS PT2522-4 open back planar tweeter is designed to deliver high efficiency with dynamic response. Thanks to a lightweight damped Polyethylene Naphthalate film diaphragm that is driven by 6 powerful neodymium magnets in a push-pull arrangement, this driver is capable of incredible transient response and low distortion. The linear 3.4 ohm impedance makes crossover design simple and minimizes the number of components required to achieve your required roll off. In addition, the open back design gives this tweeter true dipole radiation making it the perfect choice for use in open baffle speaker designs. The PT2522-4 is a perfect choice for use as a drop in replacement in existing systems or for use in new designs where low distortion and accurate response is needed.
GRS PT6816-8
Capable of delivering wide bandwidth with low distortion, the GRS PT6816-8 open back planar driver has the ability to perform well from upper midrange to the highest frequencies. With an extremely lightweight diaphragm and a neodymium motor system, this driver is capable of excellent transient response with amazing dynamics. The open back construction produces true dipole radiation which is ideal for use in open baffle designs. With a narrow footprint and minimal flange, the PT6816-8 is also ideal for line array use. Key Features Extremely low mass diaphragm provides excellent transient response and accuracy Narrow design to deliver excellent off axis consistency Multiple neodymium magnets in push pull arrangement for incredible control and low distortion Open back delivers true dipole radiation making this driver ideal for open baffle line array designs Linear impedance simplifies crossover design Shallow mounting depth for use in low profile designs The GRS PT6816-8 open back planar midrange/tweeter is designed to deliver low distortion with dynamic response. Thanks to a lightweight damped polyimide diaphragm that is driven by 18 powerful neodymium magnets in a push-pull arrangement, this driver is capable of incredible transient response and wide bandwidth. The almost linear 6.4 ohm impedance makes crossover design simple and minimizes the number of components required to achieve your required roll off. In addition, the open back design gives this tweeter true dipole radiation making it the perfect choice for use in open baffle speaker designs. With wide dispersion capabilities and minimal mounting flange, the PT6816-8 is an excellent choice for use in high output line arrays.
GRS PT2522-FP Face Plate for PT2522-4 and PT2522C-4 Planar Tweeters
By attaching the GRS PT2522-4 or PT2522C-4 planar tweeter to the PT2522-FP faceplate, you can streamline the mounting process. This faceplate simplifies the complex profile of these tweeters while offering a flush mounting ensuring diffraction effects are mitigated, as well as providing an aesthetically pleasing finish to any project!Key FeaturesAluminum faceplate for the GRS PT2522-4 and PT2522C-4 planar tweeters Simplifies the complicated profile of the PT2522/C for easy mounting Instantly improve the looks of any project Does not effect output when installed All mounting hardware included Tweeter not included Hochtöner nicht enthalten
Dayton Audio NHP25Ti-4
Dayton Audio NHP25Ti-4 1” Titanium High Power Neodymium Tweeter 4 Ohm The Dayton Audio compact NHP25Ti-4 1" titanium dome tweeter uses a high temperature neodymium motor, Ferrofluid cooling, and rear mounted heatsink for improved heat dissipation making this tweeter suitable for higher output systems and even professional line arrays. In addition, the flat response and high efficiency makes the NHP25Ti-4 an amazing value. Key Features Extremely smooth response makes for easy transition to midrange diver Over 94 dB efficiency is perfect for use in higher output designs Attached heatsink and ferrofluid cooling for increased power handling Compact cast aluminum faceplate minimizes center-to-center distance High temperature neodymium motor allows high output for extended periods Dayton Audio NHP25Ti-4 1" Titanium Dome High Power Neodymium Tweeter 4 Ohm Dayton Audio's versatile NHP25Ti-4 is a 1" titanium-dome tweeter that offers the performance of more expensive tweeters in a compact and stylish package. The small yet powerful high temperature neodymium motor with attached aluminum heatsink and Ferrofluid-filled magnetic gap reduces power compression and improves long-term power handling. In addition, the carefully designed titanium diaphragm provides accurate treble response to over 20 kHz, excellent off-axis dispersion, and superb sonic detail. The NHP25Ti-4 includes a 2.5" cast aluminum faceplate, however Dayton Audio does offer an optional 4.09" (104 mm) and 4.33" (110 mm) faceplate allowing this tweeter to be used as a drop in replace for many common sized tweeters.
Dayton Audio DC28F-8 1-1/8" Silk Dome Tweeter
Smooth-as-silk sound at an affordable price makes the Dayton Audio DC28F-8 1-1/8" Silk Dome Tweeter an ideal choice for most home DIY projects. Key Features Treated silk dome for smooth frequency response Damped rear chambers for reduced resonance Ferrofluid cooled voice coil for outstanding power handling and better damping Ideal replacement for Dayton Audio DC28FS-8 1-1/8" Silk Dome Shielded Tweeter The Dayton Audio DC28F-8 1-1/8" Silk Dome Tweeter is a great option for DIY speaker enthusiasts, as it offers amazing performance at an unbelievable price point. Featuring treated silk dome, this tweeter delivers smooth sound, while the damped rear chamber diminishes the resonance for better clarity. Thanks to the Ferrofluid cooled voice coil, this tweeter has excellent capabilities to handle high power. Replacement diaphragm 275-072
GRS PT2522C-4
With a low mass diaphragm and powerful motor, the GRS PT2522C-4 planar sealed back tweeter delivers high efficiency output with excellent transient response. The low profile sealed back allows this tweeter to be installed easily into conventional speakers without the need for a separate sub-enclosure. Remarkably smooth frequency response gives the PT2522C-4 an incredibly natural but dynamic sound. Key Features Extremely low mass diaphragm provides excellent transient response and accuracy Large diaphragm produces high efficiency and wide bandwidth Multiple neodymium magnets in push pull arrangement for incredible control and low distortion Remarkably flat response even at 30 degrees off axis Linear impedance simplifies crossover design Shallow mounting depth for use in low profile designs The GRS PT2522C-4 sealed back planar tweeter is designed to deliver high efficiency with extremely smooth response. Thanks to a lightweight damped Polyethylene Naphthalate film diaphragm that is driven by 6 powerful neodymium magnets in a push-pull arrangement, this driver is capable of incredible transient response and low distortion. The linear 3.4 ohm impedance makes crossover design simple and minimizes the number of components required to achieve your required roll off. In addition, the low profile sealed rear chamber isolates the rear side of the diaphragm for simple installation into conventional enclosures. The PT2522C-4 is a perfect choice for use as a drop in replacement in existing systems or for use in new designs where low distortion and accurate response is needed.
Dayton Audio AMTPRO-4 Air Motion Transformer Tweeter
Dayton Audio AMTPRO-4 Air-Motion-Transformer Hochtöner 4 Ohm Der Dayton Audio AMTPRO-4 Air Motion Transformer wurde für professionelle Audio- und anspruchsvolle High-Fidelity-Anwendungen entwickelt, bei denen hohe Schalldruckanforderungen mit dem Bedürfnis nach detaillierter Wiedergabe und musikalischer Finesse kombiniert werden. Wesentliche Merkmale Die gefaltete Kapton-Bändchenmembran liefert eine saubere, detaillierte und hochdynamische Wiedergabe Offene Rückseite ermöglicht Dipol- oder Kammerbeschallung Leistung und Robustheit auf Profi-Niveau für PA-Boxen, Studiomonitore oder hocheffiziente Heimwiedergabe Dayton Audio AMTPRO-4 Air Motion Transformer Hochtöner 4 Ohm Das Modell AMTPRO-4 von Dayton Audio verfügt über eine extrem große AMT-Membran mit offenem Rücken und einem leistungsstarken Neodym-Magnetsystem. Diese Kombination sorgt für eine hohe Ausgangsleistung und geringe Verzerrung über einen breiten Frequenzbereich und kann gleichzeitig große Mengen an Verstärkerleistung verarbeiten. Der AMTPRO-4 eignet sich perfekt für den Einsatz in PA-Lautsprechern, großformatigen Studiomonitoren, kundenspezifischen Kinolautsprechern oder HiFi-Lautsprechern mit extremer Leistung und kann je nach Dipolanwendung problemlos mit einer Kammer oder einer offenen Schallwand bestückt werden. Dank seiner Fähigkeit, bis zu 1200 Hz zu überbrücken, ist der AMTPRO-4 Treiber eine einzigartig effektive Lösung für die Wiedergabe von Mitten und Höhen und kann sogar als "Mittel-Hochton"-Treiber mit großer Bandbreite eingesetzt werden. Dayton Audio AMT (Air Motion Transformer) Hochtöner nutzen die Technologie des originalen Heil Air Motion Transformer, um eine extrem saubere, detaillierte und dynamische Hochtonwiedergabe zu ermöglichen. Die gefaltete Bändchenmembran eines AMT bietet eine große akustische Abstrahlungsfläche, die in einem kompakten Gehäuse untergebracht ist, und sorgt für einen extrem hohen Schalldruck, eine große Bandbreite und eine verbesserte Belastbarkeit.
GRS PT6825-8 8" Planar Mid/Tweeter 8 Ohm
Capable of delivering extremely wide bandwidth with low distortion, the GRS PT6825-8 open back planar driver is designed to deliver natural midrange response while remaining accurate to the highest frequencies. With an extremely lightweight diaphragm and a neodymium motor system, this driver is capable of excellent transient response with amazing dynamics. The open back construction produces true dipole radiation which is ideal for use in open baffle designs. Key Features Extremely low mass diaphragm provides excellent transient response and accuracy Large diaphragm produces high efficiency with incredible dynamics Remarkably wide bandwidth for controlled transition to woofer and tweeter drivers Open back delivers true dipole radiation for use in open baffle designs Linear impedance simplifies crossover design Shallow mounting depth for use in low profile designs With the ability to provide low distortion output from 500-20,000 Hz, the GRS PT6828-8 open back midrange/tweeter is an excellent choice for use in 2-way designs or even as a drop in replacement in many existing systems. Thanks to a lightweight damped polyimide diaphragm driven by 30 powerful neodymium magnets in a push-pull arrangement, this driver is capable of incredible transient response and detail. With a nearly linear 6.4 ohm impedance keeps crossover design simple with predictable final results. In addition, the open back design gives this midrange/tweeter true dipole radiation making it the perfect choice for use in high end open baffle speaker designs.
AMT U160W WITH FRONT PANEL
4 Ohm - 55x175mm - Neodymium The AMT U160W1.1 combines the highest level reserves with the decisive quality features of the AMT U-series with Mundorf diaphragm: exceptionally low K3/K5 distortion, powerful music reproduction over the entire range of use and the fine detail typical of Mundorf AMT. This makes it the first choice whenever life-performance volume needs to be realised at long listening distances - such as with very large floorstanding speakers or in home cinema use. Due to its front panel geometry, it is ideally suited for stacking several tweeters vertically in a line. This places the AMT U160W1.1 on the borderline of sound reinforcement technology. The tweeters of our AMT U.series have become very popular among demanding DIY loudspeaker builders. To meet their demands for precise, uncomplicated front mounting and a high-quality finish, every U.Series model is now also supplied with an attractive black aluminium front panel. A precisely fitting cut-out in the back of the 6mm! thick panel ensures that the AMT motor unit is perfectly centred and can be integrated flush into the baffle with an enlarged contact surface.
Dayton Audio CE32A-8 1-1/4" Mini Speaker 8 Ohm
Dayton Audio CE Series CE32A-8 1-1/4" Mini Speaker 8 Ohm Der CE32A-8 Miniatur-Lautsprecher von Dayton Audio sieht gut aus und klingt gut - und das in einem überraschend kleinen Gehäuse. Sein hochwertiges Design verfügt über die Merkmale eines großen Lautsprechers wie eine elegante schwarz eloxierte Aluminiummembran, eine Gummisicke und einen Neodymantrieb. 8 Ohm Impedanz. Wesentliche Merkmale Schwarz eloxierte Aluminium-Kalottenmembran (inverted dome) Gummisicke und Gewebespinne für geringe Verzerrungen Hochenergetischer Doppel-Neodymantrieb Dayton Audio CE Serie CE32A-8 1-1/4" Mini-Lautsprecher Dayton Audio freut sich, die neue Commercial Engineering (CE) Serie von kleinen Lautsprechern vorstellen zu können. Ingenieure, Designer und Integratoren werden davon profitieren, wie mühelos diese Lautsprecherkomponenten die vielfältigen Anforderungen erfüllen, die mit Unterhaltungselektronik und audiogestützten Projekten verbunden sind. Innerhalb der Treiberfamilie der CE-Serie sind mehrere Typen und Ausführungen erhältlich. Sie wurden entwickelt, um unabhängig von den Zielen des Systemdesigns eine hervorragende Audioqualität zu liefern und ein breites Spektrum an technischen Anforderungen zu erfüllen. Diese vielseitigen und dennoch kostengünstigen Lautsprecher sind in Größen von 28 mm (1-1/8") bis 90 mm (3-1/2") Durchmesser und mit Leistungswerten von 1,5 bis 5 Watt Dauer-RMS-Leistung erhältlich. Der Dayton Audio CE32A-8 bietet die Eigenschaften eines großen Lautsprechers in einer extrem kompakten Einheit. Er verfügt über eine Papiermembran, eine Gummirollensicke und einen hochenergetischen doppelten Neodymantrieb, der in einem robusten, spritzgegossenen Kunststoffrahmen montiert ist, der sich perfekt zum Einpressen oder Verkleben eignet. Durch sein Design eignet er sich perfekt für den Einsatz in Multimedia-Lautsprechern, kleinen Docking-Lautsprechern für tragbare Musikplayer oder kompakten Fernsehrahmen und Soundbars sowie für eine Vielzahl anderer Anwendungen.
Dayton Audio ND28F-6
Dayton Audio ND28F-6 1-1/8” Soft Dome Neodynium Tweeter This compact 1-1/8" soft dome tweeter offers the best of both worlds. A low free air resonance together with a compact faceplate. Key Features Front-mount design Center-to-center spacing as low as 2-1/2" Great top-end air and sparkle Self shielding neodymium motors Dayton Audio ND28F-6 1-1/8" Soft Dome Neodymium Tweeter This compact 1-1/8" soft dome tweeter offers the best of both worlds. A low free air resonance together with a compact faceplate. Great for MTM or line array designs.
Dayton Audio TD20F-4
Dayton Audio TD20F-4 3/4” Soft Dome Neodymium Tweeter 4 Ohm The Dayton Audio TD20F-4 uses a 3/4" silk dome to produce smooth response with excellent dispersion. At only 2-1/2" diameter and just over 1/2" deep, this tweeter is ideal for use in any compact design. Key Features 3/4" silk dome provides articulate yet non-fatiguing high frequency reproduction Exceptionally flat and smooth frequency response Ferrofluid for improved power handling and damping Neodymium magnet low-distortion motor system Dayton Audio TD20F-4 3/4" Soft Dome Neodymium Tweeter 4 Ohm Dayton Audio's TD20F-4 3/4" silk dome tweeter incorporates an optimized diaphragm that combines low mass, superb damping, and a carefully calculated dome profile offering an exceptionally flat frequency response. This, along with the low distortion neodymium motor system, ensures that high frequency content is reproduced as transparently as possible.
Dayton Audio CE32A-4 1-1/4" Mini Speaker 4 Ohm
Dayton Audio CE Series CE32A-4 1-1/4" Mini Speaker 4 Ohm Der CE32A-4 Miniatur-Lautsprecher von Dayton Audio sieht gut aus und klingt gut - und das in einem überraschend kleinen Gehäuse. Sein hochwertiges Design verfügt über die Merkmale eines großen Lautsprechers wie eine elegante schwarz eloxierte Aluminiummembran, eine Gummisicke und einen Neodymantrieb. 4 Ohm Impedanz. Wesentliche Merkmale Schwarz eloxierte Aluminium-Kalottenmembran (inverted dome) Gummisicke und Gewebespinne für geringe Verzerrungen Hochenergetischer Doppel-Neodymantrieb Dayton Audio CE Serie CE32A-4 1-1/4" Mini-Lautsprecher Dayton Audio freut sich, die neue Commercial Engineering (CE) Serie von kleinen Lautsprechern vorstellen zu können. Ingenieure, Designer und Integratoren werden davon profitieren, wie mühelos diese Lautsprecherkomponenten die vielfältigen Anforderungen erfüllen, die mit Unterhaltungselektronik und audiogestützten Projekten verbunden sind. Innerhalb der Treiberfamilie der CE-Serie sind mehrere Typen und Ausführungen erhältlich. Sie wurden entwickelt, um unabhängig von den Zielen des Systemdesigns eine hervorragende Audioqualität zu liefern und ein breites Spektrum an technischen Anforderungen zu erfüllen. Diese vielseitigen und dennoch kostengünstigen Lautsprecher sind in Größen von 28 mm (1-1/8") bis 90 mm (3-1/2") Durchmesser und mit Leistungswerten von 1,5 bis 5 Watt Dauer-RMS-Leistung erhältlich. Der Dayton Audio CE30P-4 bietet die Eigenschaften eines großen Lautsprechers in einer extrem kompakten Einheit. Er verfügt über eine Papiermembran, eine Gummirollensicke und einen hochenergetischen doppelten Neodymantrieb, der in einem robusten, spritzgegossenen Kunststoffrahmen montiert ist, der sich perfekt zum Einpressen oder Verkleben eignet. Durch sein Design eignet er sich perfekt für den Einsatz in Multimedia-Lautsprechern, kleinen Docking-Lautsprechern für tragbare Musikplayer oder kompakten Fernsehrahmen und Soundbars sowie für eine Vielzahl anderer Anwendungen.
Dayton Audio RST28F-4 1-1/8" Reference Series Fabric Dome Tweeter 4 Ohm
The Dayton Audio RST28F-4 1-1/8" silk dome Reference Series tweeter has remarkable clarity, low free air resonance, exceptional efficiency, and smooth frequency response, a combination seldom found in the industry at any price. This upgrade over the original RS28F-4 provides incredible performance at an amazing value. Key Features 1-1/8" silk diaphragm offers excellent damping and remarkable clarity Exceptional efficiency at 93.5 ±3 dB from 1.4 kHz to 20 kHz for extremely accurate response Well-designed phase bridge to balance the response in the upper octave Tuned rear chamber and high-quality Ferrofluid for extended low-end response Low-distortion motor system achieves a rare level of transparency Matches the performance of even the most expensive audiophile high-frequency transducers The Dayton Audio RST28F-4 silk dome Reference Series tweeter offers exceptional efficiency from 1,400 Hz to 20,000 Hz with an extremely natural and dynamic sound. This unique 1-1/8" silk dome and a state-of-the-art Ferrofluid cooled motor system employs copper shorting rings to ensure that high frequency content is reproduced as transparently as possible, assuring studio-quality performance. RST28F-4 tweeters not only match the look and features of the RS woofers and midranges but also the clean, detailed, and uncolored sound that characterizes the entire series. These are just a few of the features that allow these tweeters to outperform some the most expensive audiophile high-frequency transducers.
Dayton Audio ND20FB-4 Rear-Mount
Dayton Audio ND20FB-6 Rear Mount 3/4” Soft Dome Neodynium Tweeter This versatile tweeter is a huge step above the average "budget" tweeter. It has the sensitivity, smoothness, and power handling to individually do a two-way with most small woofers. Key Features Compact neodymium motors have low stray field Ferrofluid enhances power handling and helps damp resonance Front-mount pressfit design Perfect for placement in car A-pillars Center-to-center spacing as low as 1-1/2" Extremely flat and extended response Dayton Audio ND20FB-6 Rear Mount 3/4" Soft Dome Neodymium Tweeter Don't let the low price fool you! This versatile tweeter is a huge step above the average "budget" tweeter. Conceived with line array thoughts in mind, it is finally possible to achieve the inter-driver spacing needed to minimize comb filtering out to nearly 20 kHz. But their uses don't stop at line arrays-- they have the sensitivity, smoothness, and power handling to individually do a two-way with most small woofers. Give them a try for your next budget or micro speaker-- you will be pleasantly surprised!
Dayton Audio ND20FA-6
Dayton Audio ND20FA-6 3/4” Soft Dome Neodynium Tweeter This versatile tweeter is a huge step above the average "budget" tweeter. It has the sensitivity, smoothness, and power handling to individually do a two-way with most small woofers. Key Features Compact neodymium motors have low stray field Ferrofluid enhances power handling and helps damp resonance Front-mount pressfit design Perfect for placement in car A-pillars Center-to-center spacing as low as 1-3/4" Extremely flat and extended response Dayton Audio ND20FA-6 3/4" Soft Dome Neodymium Tweeter Don't let the low price fool you! This versatile tweeter is a huge step above the average "budget" tweeter. Conceived with line array thoughts in mind, it is finally possible to achieve the inter-driver spacing needed to minimize comb filtering out to nearly 20 kHz. But their uses don't stop at line arrays-- they have the sensitivity, smoothness, and power handling to individually do a two-way with most small woofers. Give them a try for your next budget or micro speaker-- you will be pleasantly surprised!
AMT-2 Air Motion Transformer
Dynavox AMT-2 Air Motion TransformerThe Dynavox AMT-2 Air Motion Transformer is a high-end tweeter and with the typical characteristicsdieses speziellen Lautsprechertyps: highly dynamic sound image, excellent impulse response, highEfficiency and low harmonic distortion. Massive, black 3 mm aluminum front panel,High-performance neodymium magnet system, folded diaphragm made of Kapton and aluminum foil.
Dayton Audio ND25TA-4
Dayton Audio ND25TA-4 1” Titanium Dome Neodynium Tweeter Dayton Audio's ND25TA-4 compact titanium dome tweeter features high output and smooth response to beyond 22 kHz, for maximum dynamic impact and excellent transient response. The high-strength neodymium motor is equipped with an aluminum heatsink for cool operation and reduced power compression. Key Features 1" titanium dome diaphragm with damped fabric surround Compact round faceplate and protective metal grill High-strength neodymium motor with heatsink and ferrofluid cooling Smooth and detailed treble response to 22 kHz and beyond Clean, modern styling and appearance Dayton Audio ND25TA-4 1" Titanium Dome Neodymium Tweeter The Dayton Audio ND25TA-4 is a versatile 1" titanium-dome tweeter that offers the performance of more expensive tweeters in a compact and stylish package. It features a Dayton Audio exclusive round faceplate design with integral perforated steel grille, and a small yet powerful neodymium motor with attached aluminum heatsink and ferrofluid-filled magnetic gap for reduced power compression and improved long-term power handling. The carefully-designed titanium diaphragm provides clean, crisp treble response to beyond 22 kHz, and delivers superb sonic detail and dynamics with low distortion. A copper pole cap further reduces distortion and inductance effects. Choose the ND25TA-4 when you need maximum dynamic impact and powerfully-rendered sonic detail to keep up with a high-output midrange or woofer. The compact round faceplate design integrates easily into your baffle design without claiming a large amount of real estate, and the integrated grill protects the titanium dome from damage.
Dayton Audio PTMini-6
Dayton Audio PTMini-6 Planar Tweeter 6 Ohm The Dayton Audio PTMini-6 is a miniature planar tweeter that is big on performance and sound quality! With 6 ohm impedance and incredibly small size this is an excellent choice for car audio or home use. Key Features Compact planar ribbon tweeter driver High output and exceptional treble definition Surface or flush mount installation Potent neodymium magnetic design Supports 4,000 Hz crossover, 12 dB/octave Dayton Audio PTMini-6 Planar Tweeter 6 Ohm The clarity, definition, and transparency of a planar tweeter is unmatched by almost any other type of tweeter. Now Dayton Audio lets you build planar technology into more compact projects with the PTMini-6 planar tweeter! The surface-mount housing design can also be flush-mounted for a world of possible uses, such as a car A-pillar tweeter, a supertweeter for a full-range driver, a rear-mounted ambience tweeter, a conventional forward-facing tweeter configuration, or even a line array! The membrane of a planar tweeter is an almost weightless ribbon of heat-resistant Kapton material and an etched aluminum conductor, enabling the performance of aluminum ribbon tweeters without the losses inherent in the transformer of a conventional ribbon tweeter. The result is a tweeter that is incredibly fast, dynamic, and smooth sounding with imperceptible distortion and excellent power handling. A crossover cut-off frequency of 4,000 Hz or higher is recommended with a 12 dB/octave filter slope.
Dayton Audio ND16FA-4
Dayton Audio ND16FA-4 5/8” Soft Dome Neodynium Tweeter 4 Ohm Dayton Audio's ND16FA-4 5/8" soft dome tweeter is perfect for use in compact 2-way systems such as desktop, surround, or portable speaker systems. With smooth response from 4,000 to 20,000 Hz this tweeter is ideal for adding more top end to many full-range drivers. Key Features Ferrofluid enhances power handling and helps damp resonance Powerful neodymium motor keeps tweeter small with impressive efficiency Compact faceplate is perfect for minimal center-to-center distances Easy installation, front mount pressfit design Perfect for placement in car A-pillars Dayton Audio ND16FA-4 5/8" Soft Dome Neodymium Tweeter 4 Ohm The versatile ND16FA-4 5/8" soft dome tweeter from Dayton Audio has the sensitivity, smoothness, and power handling for use in a 2-way design with most small woofers. The compact faceplate allows minimal center-to-center distances making these a great choice for use in 2-way designs with high crossover points. With 4-ohm impedance, this tweeter is suitable for use in both home and automotive applications. Thanks to the Ferrofluid cooled voice coil, the ND16FA-4 can handle an impressive amount of power and has excellent damping for extremely accurate response.
Dayton Audio ND25FN-4
Dayton Audio ND25FN-4 1” Soft Dome Neodynium Tweeter Element 4 Ohm Dayton Audio's ND25FN-4 compact soft dome tweeter element features high output and smooth, low-distortion sound. The high-strength neodymium motor features an aluminum heat sink for cool operation and reduced power compression. Key Features 1" treated silk dome diaphragm Faceplate-free design enables versatile custom mounting High-strength neodymium motor with heatsink and ferrofluid cooling Extremely smooth and extended treble response beyond 22 kHz Perfect for use with a waveguide or custom mounting plate Great replacement for car door tweeters Dayton Audio ND25FN-4 1" Silk Dome Neodymium Tweeter Element 4 Ohm Dayton Audio’s ND25FN-4 is a versatile 1" tweeter element for use in highly customized applications requiring smooth, clean treble output. The treated silk dome diaphragm delivers excellent detail and smoothness, while the high-strength neodymium magnet enables high output from an extremely compact size. The rear-mounted heatsink and ferrofluid-filled magnetic gap provide improved heat dissipation from the compact motor structure, for reduced power compression at high levels. A copper pole cap further reduces distortion and inductance effects. This element is identical to the round-faceplate ND25FA-4 model, but with no faceplate installed. It’s perfect for installation into a waveguide or a custom mounting plate, or in limited clearance applications such as automotive A-pillars. Simply bond the unit in place from behind, and prepare to be surprised at the clean, detailed output!
Dayton Audio RST28A-4 1-1/8" Reference Series Aluminum Dome Tweeter 4 Ohm
The Dayton Audio RST28A-4 1-1/8" aluminum dome Reference Series tweeter has remarkable clarity, low free air resonance, exceptional efficiency, and smooth frequency response, a combination seldom found in the industry at any price. This upgrade over the original RS28A-4 provides incredible performance at an amazing value. Key Features 1-1/8" aluminum diaphragm offers remarkable clarity without the typical harshness of metal domes Exceptional efficiency at 92.5 ±3 dB from 1.5 kHz to 19 kHz and a smooth frequency response Well-designed phase bridge to balance the response in the upper octave Tuned rear chamber and high-quality Ferrofluid for excellent low-end response Low-distortion motor system achieves a rare level of transparency Matches the performance of even the most expensive audiophile high-frequency transducers The Dayton Audio RST28A-4 aluminum dome Reference Series tweeter offers exceptional efficiency from 1,500 Hz to 20,000 Hz with smooth and well controlled frequency response. This tweeter's unique black anodized 1-1/8" aluminum diaphragm and state-of-the-art motor system not only match the look and features of Dayton Audio's Reference Series woofers and midranges, but also the clean, detailed, and uncolored sound you have come to expect. A specialized damped rear chamber, well-designed phase bridge, rigid mesh grill, and several distortion-reducing paths in the motor are just a few of the features that allow these tweeters to outperform some the most expensive audiophile high-frequency transducers. For applications like line arrays or compact mini-monitors that demand a smaller faceplate, an optional truncated faceplate is available.For the replacement diaphragm, see part number 275-133
Dayton Audio ND13FA-4
Dayton Audio ND13FA-4 1/2” Soft Dome Neodynium Tweeter Dayton Audio's tiny ND13FA-4 1/2" soft dome tweeter is perfect for use in compact 2-way systems such as desktop, surround, or portable speaker systems. With smooth response from 4,500 to 20,000 Hz this tweeter is ideal for adding more top end to many full-range drivers. Key Features Compact faceplate is perfect for minimal center-to-center distances Easy installation, front mount pressfit design Ferrofluid enhances power handling and helps damp resonance Powerful neodymium motor keeps tweeter small with impressive efficiency Dayton Audio ND13FA-4 1/2" Soft Dome Neodymium Tweeter 4 Ohm The versatile ND13FA-4 1/2" soft dome tweeter from Dayton Audio has the sensitivity, smoothness, and power handling for use in a 2-way design with most small woofers. The small faceplate allows minimal center-to-center distances making these a great choice for use in 2-way designs with high crossover points. With 4-ohm impedance, this tweeter is suitable for use in both home and automotive applications. Thanks to the Ferrofluid cooled voice coil, the ND13FA-4 can handle an impressive amount of power and has excellent damping for extremely accurate response.
Dayton Audio DSN25Ti-4
Dayton Audio DSN25Ti-4 1" Titanium Dome Neodymium Tweeter with Steel Frame 4 Ohm Sharing the same look as Dayton Audio's popular Designer Series drivers, the DSN25Ti-4 1" titanium dome tweeter has been optimized to deliver accurate and detailed response with remarkably high efficiency. With a compact faceplate, low distortion copper cap, and 4 ohm impedance, this tweeter is ideal for use in 2-way MTM designs. Key Features Titanium dome delivers accuracy and detail with low distortion Exceptionally flat treble response for accurate high frequency reproduction 1" diameter voice coil with ferrofluid cooling for excellent power handling High-strength neodymium motor offers low distortion and high efficiency Retains the same "family look" as the popular Designer Series woofers, subwoofers and passive radiators Dayton Audio DSN25Ti-4 1" Titanium Dome Neodymium Tweeter with Steel Frame 4 Ohm Dayton Audio's Designer Series DSN25Ti-4 1" titanium dome tweeter has everything you have come to expect from the Designer Series drivers such as smooth frequency response, low distortion, good efficiency, and even a matching frame. Driver integration and crossover designs are simple with smooth response from 2,000 to 20,000 Hz and predictable roll off on the low end. The powerful Ferrofluid cooled neodymium motor provides high efficiency allowing excellent dynamics while keeping size and weight to a minimum. Finally, the DSN25Ti-4 includes a copper cap on the pole piece to lower distortion ensuring accurate high frequency response.
Dayton Audio DC28FS-8 1-1/8" Silk Dome Shielded Tweeter
Shielded version of the famous Dayton Audio Silk Dome Tweeter. 1-1/8" silk dome with ferrofluid cooling and fully shielded motor structure. Key Features Offers smooth and detailed high frequency performance Magnetically shielded Ferrofluid cooled voice coil The shielded version of the famous Dayton Audio Silk Dome, this tweeter offers the same performance but in a CRT-safe design. Features a 1-1/8" silk dome with a ferrofluid cooled voice coil for superior damping. Compare it to drivers costing $30 to $40 more! Recommended for crossover points as low as 1,800 Hz, making it ideal for most 2-way speaker designs. 5 year warranty. Specifications: • Power handling: 50 watts RMS/100 watts max • VCdia: 1.14" • Le: 0.09 mH • Impedance: 8 ohms • Re: 5.6 ohms • Frequency response: 1,600-20,000 Hz • Fs: 813 Hz • SPL: 89 dB 1W/1m • Qms: 1.97 • Qes: 1.6 • Qts: 0.88 • Dimensions: Overall diameter: 4.33", Cutout diameter: 3.07", Depth: 1.42".
CSS Audio LD25X
The legendary LD25X has returned! Finding the patented XBL^2 in a tweeter is rare due to the challenging quality control that is required to ensure the tweeter functions as designed but offers unique benefits over other designs. The extremely flat and broad BL curve provides a larger and stronger magnetic field for the voicecoil to operate within. This leads to low levels of inter-modulation distortion by ensuring the voicecoil is always operating in the linear range even at higher powers and lower frequencies. We didn't stop there with this new iteration though. On top of the XBL^2 motor we added an additional copper cap to further reduce distortion and increase top end frequency extension. All told, you get incredibly detailed and dynamic sound reproduction in a small and elegant package.
Dayton Audio AMT3-4 Air Motion Transformer Tweeter
Dayton Audio AMT3-4 Air-Motion-Transformer Hochtöner 4 Ohm Der AMT3-4 Air Motion Transformer Hochtöner von Dayton Audio bringt Klarheit, Schnelligkeit und musikalische Finesse in Ihr Design. Die große AMT-Membran und der hochbelastbare Neo-Motor bieten eine extrem große Bandbreite und hohe Empfindlichkeit. Wesentliche Merkmale Robuste Metallfrontplatte für sichere, stabile Montage Leistungsstarke, leichte Neodym-Magnetstruktur für geringe Verzerrungen und hohen Wirkungsgrad Große Bandbreite erleichtert die Integration mit großen Midwoofern 25 Watt RMS Belastbarkeit Dayton Audio AMT3-4 Air Motion Transformer Hochtöner 4 Ohm Die großzügige Abstrahlfläche des Dayton Audio AMT3-4 erweitert den Frequenzgang von den unteren Frequenzen bis in den oberen Mitteltonbereich. Dadurch eignet sich der Schallwandler hervorragend als breitbandiger "Mittelhochtöner" in einem 2-Wege-Design mit größeren Tieftönern oder als Mitteltöner in einem 3-Wege-Design. Die robuste Metallfrontplatte verleiht dem Schallwandler ein unverwechselbares Qualitätsgefühl, während die abgedichtete hintere Kammer die Notwendigkeit einer separaten Gehäusekammer überflüssig macht. Dayton Audio AMT (Air Motion Transformer) Hochtöner nutzen die bahnbrechende Wandlertechnologie des originalen Heil Air Motion Transformer, um eine extrem saubere, detaillierte und dynamische Hochtonwiedergabe zu gewährleisten. Die gefaltete Bändchenmembran eines AMT bietet eine große akustische Abstrahlungsfläche, die in einem kompakten Gehäuse untergebracht ist, und sorgt so für eine extrem hohe Leistung und verbesserte Belastbarkeit.
Dayton Audio ND16FA-6
Dayton Audio ND16FA-6 5/8” Soft Dome Neodynium Tweeter Don't let the low price fool you! This versatile tweeter is a huge step above the average "budget" tweeter. Key Features Unique front pressfit, flush-mount design Center-to-center spacing as low as 1-3/8" Extended response with superior off-axis dispersion Compact neodymium motor is effectively self-shielded Ferrofluid enhances power handling and helps damp resonance Great replacement for car door tweeters Dayton Audio ND16FA-6 5/8" Soft Dome Neodymium Tweeter Don't let the low price fool you! This versatile tweeter is a huge step above the average "budget" tweeter. Conceived with line array thoughts in mind, it is finally possible to achieve the inter-driver spacing needed to minimize comb filtering out to nearly 20 kHz. But their uses don't stop at line arrays-- they have the sensitivity, smoothness, and power handling to individually do a two-way with most small woofers. Give them a try for your next budget or micro speaker-- you will be pleasantly surprised!
Dayton Audio AN25F-4
Dayton Audio AN25F-4 1” Soft Dome Neodymium Car Audio Tweeter Pair 4 Ohm The Automotive Neodymium Series tweeter pairs by Dayton Audio offer remarkable clarity, good off-axis dispersion, and an exceptionally flat response above 3 kHz. These tweeters are specifically designed for car audio systems, however their modern appearance and flat response curve integrate easily into any design, especially where minimal center-to-center spacing of the tweeter and woofer placement is needed. Sold in pairs. Key Features Ultra-high sensitivity of 96dB to deliver high output with modest power Exceptionally flat treble response for accurate high frequency reproduction High-strength neodymium motor provides low distortion and compact size 1" silk diaphragm for remarkable clarity and great off-axis response 1" diameter voice coil for excellent power handling All hardware included to permit flush or surface mounting Dayton Audio AN25F-4 1" Soft Dome Neodymium Car Audio Tweeter Pair 4 Ohm Dayton Audio designed the AN25F-4 tweeter to provide superb audio reproduction. The silk diaphragm offers remarkable clarity, great off-axis dispersion and an exceptionally flat response above 3 kHz. Although these tweeters where specifically designed for car audio systems, their modern appearance, high efficiency, and flat response curve integrate easily into many non-automotive designs and are especially useful in MTM and TMM designs where high efficiency and/or minimal center-to-center spacing of the tweeter and woofer placement is needed. Sold in pairs. Specifications: • Power handling: 40 watts RMS/80 watts max (with appropriate crossover) • VCdia: 1" • Impedance: 4 ohms • Re: 3.0 ohms • Frequency range: 3,000-20,000 Hz • Fs: 1619 Hz • SPL: 96 dB @2.83V/1m.
Dayton Audio AN25Ti-4
Dayton Audio AN25Ti-4 1” Titanium Neodymium Car Audio Tweeter Pair 4 Ohm The Automotive Neodymium Series tweeter pairs by Dayton Audio offer remarkable clarity, good off-axis dispersion, and an exceptionally flat response above 3 kHz. These tweeters are specifically designed for car audio systems, however their modern appearance and flat response curve integrate easily into any design, especially where minimal center-to-center spacing of the tweeter and woofer placement is needed. Sold in pairs. Key Features Exceptionally flat treble response for accurate high frequency reproduction High-strength neodymium motor provides low distortion and compact size Ultra-high sensitivity of 95 dB to deliver high output with modest power 1" titanium diaphragm for incredibly accuracy and great off-axis response 1" diameter voice coil for excellent power handling All hardware included to permit flush or surface mounting Dayton Audio AN25Ti-4 1" Titanium Neodymium Car Audio Tweeter Pair 4 Ohm Dayton Audio designed the AN25Ti-4 tweeter to provide superb audio reproduction. The titanium diaphragm offers remarkable accuracy, great off-axis dispersion and an exceptionally flat response above 3 kHz. Although these tweeters where specifically designed for car audio systems, their modern appearance, high efficiency, and flat response curve integrate easily into many non-automotive designs and are especially useful in MTM and TMM designs where high efficiency and/or minimal center-to-center spacing of the tweeter and woofer placement is needed. Sold in pairs. Specifications: • Power handling: 40 watts RMS/80 watts max (with appropriate crossover) • VCdia: 1" • Impedance: 4 ohms • Re: 3.11 ohms • Frequency range: 3,000-20,000 Hz • Fs: 1744 Hz • SPL: 95.5 dB @2.83V/1m.
CSS Audio LD22
CSS Audio LD22The CSS LD22 high-performance tweeter uniquely fits between the usual standard tweeters with19mm (3/4 ") and 25 mm (1") voice coils. A 22mm aluminum voice coil with copper cladding anda wide suspension ensures a low Fs and thus supports a deep coupling to theCrossover. A rear chamber and an external neodymium ring magnet ensure very lowCompression distortions than would be possible with conventional designs. Carefully selectedMaterials and the coated fabric dome enable reproduction up to 40 kHz. Test Conclusion Hobby HiFi 1/2020; CSS provides with the LD22 an excellent dome tweeter, usable from 2000 Hertz and thanks toNeodymium drive pleasantly compactly built. Parameter Nominal size: 22 mm Fs: 870 Hz SPL 89 dB @ 2.83V/1M Nom Imp: 4 ohm Re: 3.6 ohm Mms: 0.27 g Bxl: 1.7 Cms: 0.15 mm/N Vas: 7.7 ml Rms: 0.97 Ns/m Qms: 1.4 Qes: 1.69 Qts: 0.77 Voice coil inside diameter: 22 mm Voice coil winding height: 1.6 mm Air gap height: 2.5 mm Le: 40 μH Xmax: ±0.45 mm Sd: 6.1 cm² Empfohlener Frequenzbereich: 2-30 kHz
Dayton Audio DC25T-8 1" Titanium Dome Tweeter
Features a ferro fluid cooled aluminum voice coil and a rubber surround. The 1" titanium dome and precision phase lens, provide very natural sounding high frequency reproduction. Key Features Great replacement for the Dayton DC25TS-8 1" Titanium Dome Shielded Tweeter
Dayton Audio DC28F-8RD 1-1/8" Silk Replacement Diaphragm
Replacement Diaphragm for Dayton Audio DC28F Series tweeters